Friday 19 April 2013

HTC One X AT&T(PJ8310000) Unbrick, IMEI, SuperCID repair supported Repairing bricked HTC OneX (PJ8310000) is easy with the RIFF Box.


  Phone is auto powered on with USB Data Cable connected to the PC. Battery presence may be required.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.09.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PJ8310000’.
To resurrect HTC OneX (PJ8310000):
  •  Solder JTAG cable to HTC OneX (PJ8310000) JTAG pads;
  •  Insert USB Data cable into board and PC;
  •  Make sure HTC OneX (PJ8310000) is selected in the list of models;
  •  If you use battery, press Power On key;
  •  Click Resurrect button;
  •  Wait till software signals a successful operation completion;
  •  Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
  •  Disconnect PC cable;
  •  Insert battery;
  •  Hold ‘Volume Down’ key and press ‘Power ON’ button.

Micromax A50 MTK6573 Read Flash,Format,Pattern Lock Remove

Micromax A50 MTK6573 Read Flash And Pattern Lock Remove Done BY Volcano Box



Read Flash

Read Info

Fill Address


Format Success

Android Galaxy Note N7100 MTK 6577 Read Flash Done




Android Galaxy Note N7100 MTK 6577 Read Flash Done


Androiad galaxy note n7100 mtk 6577 read flash done by volcano box
About phone
PHONE INBUILT MEMORY 4GB
RAM 512MB
MT6577
Hardware : SMDK4x12
Model : GT-N7100
Build number : JRO03C.N7100ZSALIA
Build date UTC : 20130117-094416
Android v : 4.1.1
Kernel v : 3.0.31-178067 (se.infra@SEP-113) (gcc version 4.4.3 (GCC) ) #1 SMP Thu Jan 17 17:41:04 CST 2013
Uboot build v : MAIN2.2.ubt.3634
LCD Driver IC : 1-otm8009a_6575_dsi
Baseband v: MAUI.11AMD.W12.22.SP.V5, 2012/07/21 12:28






Download Full Link & Tips
Galaxy Note N7100

  1. Download the update file, Odin and Samsung KIES on your computer.
  2. The download link for the Jelly Bean 4.1.2 update is Download.
  3. You can get Odin from Download and Samsung KIES from Download.
  4. Now, on the computer extract the update file and install Odin.
  5. Also, install the proper drivers for your phablet by using Samsung KIES.
  6. On the computer open Odin and turn off your phone.
  7. Reboot the same into download mode by pressing the Volume Down, OK and Power buttons at the same time.
  8. With the phablet booted in download mode, take the USB cable and use it for connecting the device with the computer.
  9. Once you connect the devices, on Odin the ID:COM section should be yellow or blue and the “added” message should be displayed.
  10. If not, you will have to re-install the drivers on the computer (first turn off Odin and unplug the USB cable) and repeat the procedure from the beginning.
  11. From Odin now select “PDA” and pick the update file from the PC.
  12. Up next, click on “Start” for beginning the update operation.
  13. In the end, on Odin the “pass” message should be displayed.
  14. You can then unplug the USB cable and reboot your Galaxy Note 2.
Now, here are the most common issues that might appear while using Odin and trying to flash an official update: first, if Odin gets stuck in the middle of the installation procedure here is what you need to do: close Odin, disconnect the phablet from the computer, force restart the handset, re-install the drivers on the PC and then repeat all the steps from the beginning.
Then, also, in the end you might get a loop boot instead of a normal one; if that happens here is what you need to do: reboot your Note 2 into recovery mode. Then, by using the recovery mode menu wipe the system by selecting “wipe data factory reset” and “wipe cache partition; next, end the process by choosing “+++go back+++” and “reboot system now”.
So, that was all for today; now you know how to easily and manually update your Samsung Galaxy Note 2 N7100 to official Android 4.1.2 Jelly Bean XXDMB5 OS. Test the new software and do tell us how the same runs on your phablet. Use the comments area from below for sharing your impressions and thoughts with us and with other users as well. Also, stay close for further tutorials and Android related tips and tricks.


Android Galaxy Note N7100 MTK 6577 Read Flash Done

I9300 Imei Repair Done Z3X Box





Selected model: I9250
Selected port: COM4 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Model: GT-I9300
Android version: 4.0.4
Product code: Not Active
Phone version: I9300XXLE8
PDA version: I9300XXALE8
CSC version: I9300OJVALE7
IMEI: Unknown
Checking Super user right... true
Reading data from phone... OK
Writing data to phone... OK
Rebooting phone... OK
Checking phone at COM4 OK
Reading phone info...
Software version:
IMEI:
Product code:
Bypass MSL... OK
Repairing IMEI... OK
Repair done
Reseting... OK
Done with Samsung Tool v.13.7

I9300 Imei Repair Done Z3X Box 

Android TM Tablet unbootable OS 2.2 Kernel 2.6.32 Build Number V1.5.1


 Android TM Tablet unbootable OS 2.2 Kernel 2.6.32 Build Number V1.5.1


Tablet will not start 




Android TM OS 2.2 
Kernel 2.6.32 
Build Number V1.5.1


Solution to this problem, only valid for tablets 7 " .


UDROIDX 1.5.5      


NEWEST. Flash Player ready,  Improved  WIFi- Sound-Battery-New Launcher.
FASTEST. Ready to install on a lot of  WM8650 powered tablet.

Built on the 1.5.5 firmware WM8650 ; 


BEFORE FIRMWARE UPDATING please  back-up the env_uboot and wmt_scriptcmd files from your devices factory firmware you could need it later if  env_uboot in list are not working for you!!!

To install do the following:
Format a SD card to FAT32 
Extract the contents of the zip file to your SD card.

Sure you are able to do the following:

Choose your env.uboot file under  Firmwareinstalle/env according your device and rename env_uboot, delete all the others you  founded in  directory . 

Eventually insert SD card into your device and power on ; upgrade will run automatically. Once  it’s finished wait 1 min. before removing your SD card . 
The device will reboot and you can have a cup of coffe!!  
PLEASE WAIT… and be patient,  it needs 4-5 min.

The system loading screen stucked for more than 5 minutes , NO PANIC ...... try another env_uboot  or BETTER IDEA  use the env_uboot and wmt_scriptcmd files from your devices factory firmware.

Known BUGS: Battery indicator 100%

Thanks  EVERYBODY who helped ! 



Use at your own risk  !!!!!